Product Description:

SILICOcrete TRG is a high-performance premixed mortar designed for effective filling of Tie-Rod Gap / opening remaining in MIVAN type or normal type of shuttering technology. The product is designed to flow and travel and yet remain cohesive when filled by hand or by machine while being filled into the tie-rod opening so that

TECHNICAL PARAMETERS

Appearance

Grey Free Flowing Powder

Type of Sand

Precisely graded Gujarat River Sand

Sand Gradation

0mm – 1mm

Wet Density

2100 kg/m3 - 2200 kg/m3

Compressive Strength

40MPa or 60MPa or 80MPa in 28 days

Shrinkage Compensated

Expanded Grout

Water Powder Ratio

15.5% to 16.5%

Workability

Cohesive, Pasty Consistency for ease of hand application (At Specified W:P ratio mixed in high shear mixer)

Pot Life

45 mins - 60 mins (depending on weather conditions)

Shelf Life

3 months from the date of manufacturing, if stored in proper sealed bag away from moisture

Packaging

25 kg per bag

BENEFITS
METHOD OF APPLICATION
WARRANTY

The Products supplied by the Company are warranted to comply with the Product Specifications mentioned in the Product Brochure, provided they are applied and used in conformance with the processes and procedures described in the Brochure and as per the Standard Civil Engineering Practices.

In the unlikely event that the Products are found to be not in compliance with the mentioned specifications, the Company undertakes to replace the Products that are specifically determined to be non-compliant. Any suspected defects or non-compliance of the Products must be reported to the Company in writing within 72 hours of being detected or within 45 days of the supply of the Products, whichever is earlier. The Company shall have the right to inspect the area where the suspected defects are detected and in case any such suspected defect is determined to be caused specifically due to a deficiency in the Products supplied by the Company, the Company undertakes to provide replacement only for the specific area where the defective Product was applied, and not for the whole room, floor, building, or project where the Company’s Products may have been used.

Since the Company does not have control over the installation or application or end use of the Products, the Warranty shall not cover any defects that may be caused due to defective or faulty or unskilled workmanship, application, curing, or treatment of the Company’s Products. The Warranty is limited only to replacement of the Products in question and does not cover any incidental and consequential costs or damages including, but not limited to, the costs of removal and reapplication of the Products, delays, loss of profits, or any other liabilities that the purchaser may incur towards any third parties.

The above Warranty is the complete set of Warranties offered by the Company on its Products and overrides any other Warranties that may be implied or expressed in any other Product Literature or that may erroneously be inferred by the purchaser through interactions with the Company’s representatives or with any consultants, architects, etc.

The Company may, in the interests of customer service, relax the above Terms of Warranty. Any such relaxation shall be at the sole discretion of the Company and shall not be taken to be a precedent for the future. Such relaxation can only be authorized in writing by the CEO / Directors of the Company and no Company representative shall have any rights to relax the Terms of the Warranty without explicit authorization in writing from the CEO / Directors.

DISCLAIMER

All recommendations, suggestions, statements and technical data provided in this Leaflet are based on the best current knowledge available and are given for illustrative and informative purposes only and the Company does not bear without any responsibility for any loss or damages that may be caused by the use / misuse of such data.

It is assumed that all Standard Civil Engineering Practices shall be adopted for the use and application of the Company’s Products and all information provided in this Leaflet is based on the above assumption. The Company shall not be responsible for any loss or damages that may be caused by a deviation from the Standard Civil Engineering Practices or by any use or application of the Company’s products not in consonance with the information provided in this Leaflet.

The Company supplies products as per the Specifications provided in this Leaflet, and all the information in this Leaflet is for general guidance of the purchasers only. It is not possible, in this Leaflet, to provide information with respect to all potential uses and applications of the Company’s Products and for the various site conditions where the Products may be used.

Therefore, the Company makes no claims herein as to the particular suitability or fitness of the Products for specific applications or purposes. The Company may be contacted directly, if any additional information is required for any specific use or application of its Products, prior to the purchase and use of the Company’s Products by the purchaser.

The Company is continuously striving to improve and develop its products to better meet the industry requirements and to provide superior performance. Therefore the Company reserved the right to modify or improve the Products’ specifications or the information in this Leaflet at any time, without notice. The latest Products’ specifications and information can be obtained by directly contacting the Company.

The Company, as used above, shall refer exclusively to M/s Precise Conchem Private Limited as represented by its Board of Directors, and any communication directed to the Company may be preferred to the contact details of the Company, as provided in this Leaflet.