Silico Con

The SilicoCon Drymix is a kiln dried, pre-blended, factory-produced prescribed concrete mix, incorporating standardised binders, Graded sand and aggregates, with a guaranteed cement content and mix proportions.

SilicoCon Concrete Mix is a general purpose Bag Drymix concrete, it is is a kiln dried, pre-blended, factory-produced prescribed concrete mix, incorporating standardised binders, Graded sand and aggregates, with a guaranteed cement content and mix proportions.

It is suitable for concrete bases, mortar beds, Pouring Slabs, shed floors, post erection, walkways, steps, fill deep holes, general repair work and other non-structural applications.

SilicoCon is manufactured by M/s Precise Conchem Pvt. Ltd., at their plant located at GIDC Panoli, Bharuch District of Gujarat in an automated process according to formulations based on various products studies and research undertaken. The plant is one of the most modern Plants in India, in which all the critical manufacturing processes and operations are completely controlled by P.L.0 SYSTEMS (Programmed Logic Controller).

Download PDF
Features And Benefits
  • Consists of a carefully proportioned blend of high quality materials including rounded river run sands and aggregates, Portland cement and special concrete admixtures.
  • The performance and convenience makes it particularly suited for concrete jobs around
  • Achieves a 28-day compressive strength as per requirements.
Advantages Of Dry Pack Mortar
  • Used for Interior and Exterior applications
  • Uniform and consistent quality
  • Jobsite mixing of sand and cement is no longer needed
  • It can be tamped, compacted and filled easily
  • It guarantees a consistent mix on large jobs
  • Ensures Less Wastage and saves time
Benefits
  • Reduced paint consumption
  • Superb White Finishing
  • Saves time
  • Cost effective
Technical Data

Comparative analysis of various grade of concrete

Parameters

M20

M25

M30

M35

M40

7 Days (Mpa)

16- 18

18 - 20

24 - 26

28 - 30

30 - 32

28 Days (Mpa)

22 - 25

28 - 30

32 - 35

37 - 40

42 - 45

Water Requirements

9 - 10%

9 - 10%

9 - 10%

9 - 10%

9 - 10%

Flow (mm)

190 - 200

190 - 200

190 - 200

190 - 200

190 - 200

Fresh Wet Density

2.25 - 2.35

2.25 - 2.35

2.25 - 2.35

2.25 - 2.35

2.25 - 2.35

Packaging (Kgs)

50

50

50

50

50

Yield Per Bag (M3)

0.022 - 0.024

0.022 - 0.024

0.022 - 0.024

0.022 - 0.024

0.022 - 0.024

Initial Setting Time (Mins)

180 - 200

180 - 200

180 - 200

180 - 200

180 - 200

Final Setting Time (Mins)

230 - 250

230 - 250

230 - 250

230 - 250

230 - 250

Mixing Ratio
  • 1 (Gypsum Powder & Water By Volume)
Mixing Instructions

The contents of the bag can be mechanically mixed in a free fall mixer for 3-4 minutes or hand mixed by pouring the contents of the bag onto a clean flat surface and slowly adding clean water in increments and mixing continuously, until the desired workability is achieved. For optimum results, approximately 9 to 10% of clean water should be used per bag. The concrete should be used within 60 minutes of water addition.

Refrain from excessive water addition as this will weaken the mix, delay setting times and adversely affect durability. There is no need to add further additives or admixtures to the material on site as all required plasticizers and workability aids are already incorporated into the mix.

For optimum results, the concrete should be cured for at least seven days after laying by covering with plastic sheeting or another suitable material. Similar measures should be taken where appropriate to protect the concrete from the effects of the sun, wind, rain and frost.

Storage

Keep in dry place and off the ground

Packaging

50 Kg HDPE Bags